Operating Instructions
FRIDGE
Contents
GB
Installation, 2-4
Positioning and connection
Reversible doors
GB
English,1
Description of the appliance, 5
Overall view
Start-up and use, 6
Starting the appliance
Using the refrigerator to its full potential
Using the freezer to its full potential
Maintenance and care, 7
Switching the appliance off
Cleaning the appliance
Avoiding mould and unpleasant odours
Defrosting the appliance
Replacing the light bulb
TFA 1
Precautions and tips, 8
General safety
Disposal
Respecting and conserving the environment
Troubleshooting, 9
Assistance, 10
Fitting a new plug
GB
IMPORTANT:
WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE...
Green and Yellow - Earth
Blue
Brown
- Neutral
- Live
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
-
Connect Green and Yellow wire to terminal marked
'E' or or coloured Green and Yellow.
-
-
Connect Brown wire to terminal marked 'L' or
coloured red or brown.
Connect Blue wire to terminal marked 'N' or
coloured Black or Blue.
If a 13amp plug (BS 1363) is used it must be
fitted with a 13amp fuse. A 15amp plug must be
protected by a 15amp fuse, either in the plug or adaptor
or at the distribution board.
If you are in any doubt about the electrical
supply to your machine, consult a qualified
electrician before use.
CE Marking certifies that this appliance conforms to
the following EEC directives :
Low Voltage Equipment - 73/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC
& 93/68/EEC
3
Reversible doors
GB
Warning: Before attempting to remove the door, switch off the electrical supply and pull out the mains plug.
It is recommended that you remove any loose items/fittings from inside the appliance and place food into insulated containers
whilst carrying out this operation.
You may require assistance to carefully lay the appliance onto its back onto suitable protective materials (i.e. original packaging).
Remove the door
1. Lay down the appliance on its back.
2. Unscrew, remove and retain the bottom hinge pin.
3. Slightly open the door and slide downward, remove and carefully place to one side.
4. Unscrew the hinge pin from the top right hand side and refit the pin into the hole in left hand side.
5. Use a thin blunt instrument to remove the top and bottom hinge bushes and blanking plugs from the
door, take care not to mark the door handle. Reposition the blanking plugs and bushes on the opposite side.
3
4
2
1
5
Replacing the door
1 .Carefully slide the door upward into the hinge pin.
2 .Fit the bottom hinge pin making sure that the door is aligned to the cabinet.
3. Carefully stand the appliance upright in it’s required location and make sure it is sitting level on the floor. Open and
close the door checking that the gasket makes a good seal without any gaps when the door is closed.
Note: Replace loose items/fittings back into the appliance and leave for at least 15 minutes before switching back on.
1
3
2
4
Description of the
appliance
Overall view
GB
The instructions contained in this manual are applicable to different model refrigerators. The diagrams may not
directly represent the appliance purchased.
TEMPERATURE control
Removable lidded
shelf with EGG TRAY
FREEZER and
STORAGE
compartment
Removable
multipurpose
SHELVES•
SHELVES•
HINGED shelf
Drain for DEFROST
Compartment for a
WATER
2 LITRE BOTTLE
FRUIT and
VEGETABLE bin
BOTTLE shelf
Levelling FEET
• Varies by number and/or position.
5
Start-up and use
Starting the appliance
SHELVES: with or without grill.
Due to the special guides the
shelves are removable and the
height is adjustable (see
GB
! Before starting the appliance, follow the installation
instructions (see Installation).
diagram), allowing easy storage
of large containers and food.
Height can be adjusted without
complete removal of the shelf.
! Before connecting the appliance, clean the
compartments and accessories well with lukewarm
water and bicarbonate.
1. Insert the plug into the socket and ensure that the
internal light illuminates.
2. Turn the TEMPERATURE ADJUSTMENT knob to an
average value. After a few hours you will be able to
put food in the refrigerator.
Using the refrigerator to its full potential
• Use the TEMPERATURE ADJUSTMENT knob to adjust
the temperature (see Description).
• Place only cold or lukewarm foods in the compartment,
not hot foods (see Precautions and tips).
• Remember that cooked foods do not last longer than
raw foods.
• Do not store liquids in open containers. They will
increase humidity in the refrigerator and cause
condensation to form.
Setting the temperature
The temperature inside the refrigerator compartment
automatically adjusts itself according to the position of
the thermostat knob.
We recommend, however, a medium position.
The cooling section of the refrigerator is located inside
the back wall of the refrigerator compartment for
increased space and improved aesthetics. During
operation, the back wall will be covered in frost or water
droplets depending on whether the compressor is
operating or paused. Do not worry, the refrigerator is
functioning normally.
Using the freezer to its full potential
• Do not re-freeze food that is defrosting or that has
already been defrosted. These foods must be cooked
and eaten (within 24 hours).
If the TEMPERATURE ADJUSTMENT knob has been set
on high values with large quantities of food and with a
high ambient temperature, the appliance can operate
continuously, resulting in excessive frost formation and
excessive energy consumption: compensate for this by
shifting the knob towards lower values (defrosting will
occur automatically).
• Fresh food that needs to be frozen must not come into
contact with food that has already been defrosted.
• Do not place glass bottles which contain liquids, and
which are corked or hermetically sealed in the freezer
because they could break.
In static appliances, the air circulates in a natural way:
the colder air tends to move downwards as it is heavier.
The food should be stored as follows:
• The maximum quantity of food that may be frozen daily is
indicated on the plate containing the technical properties
located on the bottom left side of the refrigerator
compartment (for example: Kg/24h: 4)
Arrangement inside the
Food
refrigerator
Above the fruit and vegetable
bins
Fresh fish and meat
! Do not open the door during freezing.
Above the fruit and vegetable
Fresh cheese
bins
! If there is a power cut or malfunction, do not open the
freezer door. This will help maintain the temperature inside
the freezer, ensuring that foods are conserved for at least
9 -14 hours.
Cooked food
On any shelf
Salami, bread loaf,
chocolate
On any shelf
Fruit and vegetables In the fruit and vegetable bins
Eggs On the shelf provided
Butter and margarine On the shelf provided
! If the room temperature drops below 14°C for an
extended period of time, the ideal temperature will not be
reached in the freezer compartment and food preservation
will be reduced.
Bottles, drinks, milk
On the shelf provided
6
Maintenance and care
Switching the appliance off
Defrosting the freezer compartment
GB
During cleaning and maintenance it is necessary to
disconnect the appliance from the electricity supply:
It is not sufficient to set the temperature adjustment knobs
on 0 (appliance off) to eliminate all electrical contact.
Remove frost regularly using the special scraper
provided. If the frost layer is greater than 5 mm, it is
necessary to defrost manually:
1. Set the TEMPERATURE ADJUSTMENT knob to the
position
0
.
Cleaning the appliance
2. Wrap frozen foods in newspaper and place them in
another freezer or in a cool place.
3. Leave the door open until the frost has melted
completely. This can be made easier by placing
containers with lukewarm water in the freezer
compartment.
4. Clean and dry the freezer compartment carefully
before switching the appliance on again.
5. Wait for approximately 2 hours, i.e. until the ideal
storage conditions have been restored, before
placing food in the freezer compartment.
• The external and internal parts, as well as the rubber
seals may be cleaned using a sponge that has been
soaked in lukewarm water and bicarbonate of soda or
neutral soap. Do not use solvents, abrasive products,
bleach or ammonia.
• The removable accessories may be soaked in warm
water and soap or dishwashing liquid. Rinse and dry
them carefully.
• The back of the appliance may collect dust which can
be removed by delicately using the hose of a vacuum
cleaner set on medium power. The appliance must be
switched off and the plug must be pulled out before
cleaning the appliance.
Replacing the light bulb
To replace the light bulb in the refrigerator compartment,
pull out the plug from the electrical socket. Follow the
instructions below.
Avoiding mould and unpleasant odours
• The appliance is manufactured with hygienic materials
which are odour free. In order to maintain an odour
free refrigerator and to prevent the formation of stains,
food must always be covered or sealed properly.
• If you want to switch the appliance off for an extended
period of time, clean the inside and leave the door
open.
Access the light bulb by
removing the cover as
indicated in the diagram.
Replace it with a similar
light bulb within the power
range indicated on the
cover (10W ).
Defrosting the appliance
! Follow the instructions below.
Do not speed up the defrosting process by using any
devices or tools, you may damage the refrigeration
circuit.
The refrigerator has an automatic defrosting function:
water is ducted to the
back of the appliance by a
special discharge outlet
(see diagram) where the
heat produced by the
compressor causes it to
evaporate. It is necessary
to clean the discharge
hole regularly so that the
water can flow out easily.
7
Precautions and tips
! The appliance was designed and manufactured in
compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
Disposal
GB
• Observe local environmental standards when
disposing packaging material for recycling purposes.
• The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on
human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the
appliance it must be separately collected.
This appliance complies with the following
Community Directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and
subsequent amendments;
-89/336/EEC of 03.05.89 (Electromagnetic
Compatibility) and subsequent amendments;
- 2002/96/CE..
General safety
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
• The appliance was designed for domestic use inside
the home and is not intended for commercial or
industrial use.
• The appliance must be used to store and freeze food
products by adults only and according to the
instructions in this manual.
Respecting and conserving the
environment
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
• Install the appliance in a fresh and well-ventilated
room. Ensure that it is protected from direct sunlight
and do not place it near heat sources.
• Do not touch the appliance with bare feet or with wet or
moist hands and feet.
• Try to avoid keeping the door open for long periods or
opening the door too frequently in order to conserve
energy.
• Do not touch the internal cooling elements: this could
cause skin abrasions or frost/freezer burns.
• When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
• Do not fill the appliance with too much food:
cold air must circulate freely for food to be preserved
properly. If circulation is impeded, the compressor will
work continuously.
• Before cleaning and maintenance, always switch off
the appliance and disconnect it from the electrical
supply. It is not sufficient to set the temperature
adjustment knobs on (appliance off) to eliminate all
electrical contact.
• Do not place hot food directly into the refrigerator. The
internal temperature will increase and force the
compressor to work harder and will consume more
energy.
• In the case of a malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance.
• Defrost the appliance if ice forms (see Maintenance).
A thick layer of ice makes cold transference to food
products more difficult and results in increased
energy consumption.
• Do not use devices or tools other than the special
scraper provided inside the compartments.
• Regularly check the door seals and wipe clean to
ensure they are free of debris and to prevent cold air
from escaping (see Maintenance).
• Do not put ice cubes taken directly from the freezer
into your mouth.
• Do not allow children to tamper with the controls or
play with the appliance. Under no circumstance should
they be allowed to sit on the bins or to hang from the
door.
• Keep packaging material out of the reach of children! It
can become a choking or suffocation hazard.
8
Troubleshooting
If the appliance does not work, before calling for Assistance (see Assistance), check for a solution from the following list.
GB
Malfunctions:
Possible causes / Solutions:
The internal light does not
illuminate.
• The plug has not been inserted into the electrical socket, or not far
enough to make contact, or there is no power in the house.
The refrigerator do not cool well.
• The door do not close properly or the seals are damaged.
• The door are opened too frequently.
• The TEMPERATURE ADJUSTMENT knob is not in the correct position
• The refrigerator have been over-filled.
The food inside the refrigerator is
beginning to freeze.
• The TEMPERATURE ADJUSTMENT knob is not in the correct position.
• The food is in contact with the back inside wall of the refrigerator.
The motor runs continuously.
• The door is not closed properly or is continuously opened.
• The outside ambient temperature is very high.
The appliance makes a lot of noise.
• The appliance has not been installed on a level surface (see Installation).
• The appliance has been installed between cabinets that vibrate and
make noise.
• The internal refrigerant makes a slight noise even when the compressor is
off. This is not a defect, it is normal.
The back wall of the refrigerator unit
is covered in frost or droplets of
wate.
• This shows the appliance is operating normally.
There is water at the bottom of the
refrigerator.
• The water discharge hole is blocked (see Maintenance).
9
Assistance
Before calling for Assistance:
• Check if the malfunction can be solved on your own (see Troubleshooting).
GB
• If after all the checks, the appliance still does not operate or the problem persists, call the nearest Service
Centre
model
serial number
Communicating:
• type of malfunction
• appliance model (Mod.)
• serial number (S/N)
This information can be found on the data
plate located on the bottom left side of the
refrigerator compartment.
TI
93139180000
Cod.
S/N 704211801
Mod. RG 2330
220 - 240 V-
Fuse
A
Max 15 w
50 Hz 150 W
W
Class
Freez. Capac
340
75
Total
Net
Gross
Bruto
Brut
Gross
Bruto
Brut
Gross
Bruto
Brut
Poder de Cong Clase
N
Util
Classe
kg/24 h 4,0
Utile
Pressure
HIGH-235
LOW 140
Compr.
Syst.
Test
R
134 a
P.S-I.
kg 0,090
Kompr.
Made in Italy 13918
Never call on unauthorized technicians and always refuse spare parts which are not originals.
10
GB
11
195051962.00
03/2005
-
Xerox Business Services
GB
12
|