18. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A.
B.
C.
D.
If the power-supply cord or plug is damaged.
If liquid has spilled, or objects have fallen into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions, as an improper
adjustment of other controls may result in damage and will often require extensive work
by a qualified technician to restore the product to its normal operation.
If the product has been dropped or damaged in any way, and the product exhibits a
distinct change in performance-this indicates a need for service.
E.
19. Replacement Parts - When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
20. Safety Check - Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper operating
condition.
21. Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. Heat - The product should be situated away from heat sources such as radiators, heat
registers, stoves or other products(including amplifiers)that produce heat.
SAVE THESE INSTRUCTIONS
2
CAUTION:
z
In order to shut off the power to this product completely, unplug the power cord from the wall
outlet. be sure to unplug the unit if you do not intend to use it for an extended period of time
such as a vacation.
z
z
Do not remove the protective housing.
Use of controls and adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
z
If this product develops trouble, contact qualified service centers, and do not use the product in
a defective states.
SAFETY PRECAUTIONS
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION:
Use of controls or adjustments or performance of procedures other than those specified may result
in hazardous radiation exposures.
CAUTION
RISK OF ELECTRIC SHOCK - DO NOT OPEN
To reduce the risk of electric shock, do not remove cover or back.
No user serviceable parts inside. Refer servicing to qualified service personnel.
The light flash with arrowhead symbol, within an equilateral triangle, is intended to alert
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION:
For compact disc units only: invisible laser radiation when open and interlock failed or
defeated. Avoid direct exposure to laser beam.
3
Before Use
1. Choose unit installation location carefully. Avoid placing it in direct sunlight or close to a source
of heat. Also avoid locations subject to vibrations and excessive dust, cold or moisture. Keep
away from sources that hum, such as transformers or motors.
2. Do not open the cabinet as this might result in damage to the circuitry or electrical shock, if a
foreign object should get into the set, contact your dealer.
3. Be sure not to handle discs with dirty fingers. Never insert a disc that has a crack on the
surface.
4. When removing the power plug from the wall outlet, always pull directly on the plug, never pull
the cord.
5. To keep the laser pickup clean, do not touch it, and do not forget to close the disc tray.
6. Do not attempt to clean the unit with chemical solvents as this might damage the finish. Use a
clean, dry cloth.
7. Keep this manual in a safe place for future reference.
Beware of Condensation
When the radio is moved from a cold or warm place, or is used after a sudden temperature change,
there is a danger of condensation. Water vapor in the air could condense on the mechanism. To
prevent this, if you are going to use the radio in a condition where condensation could occur, you
should leave the radio for 1 or 2 hours after plugging it into an AC outlet depending on the amount
of condensation. If this is done, the radio will stabilize at the temperature of its surroundings.
LOCATION OF CONTROLS
1. VOLUME/POWER ON/OFF KNOB
2. LED DISPLAY
3. OPEN/CLOSE BUTTON
4. F.R BUTTON
5. F.F BUTTON
17
6. STOP BUTTON
7. PLAY/PAUSE BUTTON
8. CD BUTTON
9. PHONO BUTTON
10. AM BUTTON
11. FM BUTTON
12. RADIO DIAL SCALE
13. FM STEREO INDICATOR
14. TUNING BUTTON
15. FM ANTENNA
16. POWER CORD
17. CASSETTE PLAYER
18. ADAPTER FOR 45 RPM RECORDS
19. TONE ARM
20. SPEED CONTROL SWITCH
21. SECURITY HOOK
22. TONE ARM REST
23. TURNTABLE
24. LARGE CHROME SCREW
25. QUE-LEVER
4
Handling a record, tape or compact Disc
Compact Disc
Handing the Discs:
This unit has been designed specifically for sound reproduction from compact discs bearing the
mark
.
No other discs can be used.
z
z
z
z
z
Always place the compact disc in the disc tray with the label facing upward. (Compact discs can
be played only on one side).
To remove a disc from its storage case, press down on the centre of the case and lift the disc
out, holding it carefully by the edge.
Fingerprints and dust should be carefully wiped off the disc recorded surface with a clean cloth
(not included).
Never use chemicals such as: record sprays, anti-static sprays or fluid, benzene or thinner to
clean compact discs. Such chemicals will do irreparable damage to the disc's plastic surface.
Discs should be returned to their cases after use to avoid serious scratches that could cause the
laser pick up to skip.
z
z
z
Do not expose discs to direct sunlight or high humidity and temperature for extended periods.
Do not stick paper or write anything with a ballpoint pen on the surface of the label side.
Do not use irregular shaped CD's (octagonal, heart-shape, etc.), all of which can damage the
unit.
Preparation for Use to the mains
1. Connect the AC power cord to the mains.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
2. The silver screw protects the phonograph chassis during transportation. If the speed of your
phonograph seems slow or you hear a rubbing sound, adjust the screw with a coin to correct the
balance of the turntable.
5
How to Replace the Turntable Stylus
Removing old stylus
1. Set a screwdriver at the tip of the stylus and push down to the direction
"A".
2. Remove the stylus by pulling it down and forward.
Installing a new stylus
1. Hold the tip of the stylus and insert the other edge by pressing in the
direction "B".
2. Push up in the direction "C" until it locks at the tip.
Basic Operation
1.Power on.
Connect the power plug into the wall outlet.
Turn the unit on by turning the volume knob
clockwise. The FM Band Indicator lights.
2.Select the source.
3. Adjust the volume.
6
Listening to a Record
1. Press the PHONO button.
2. Select player speed.
3. Put a record onto the turntable (use the 45 rpmadaptor
provided when playing a single record).
4. Remove the tone arm-rest holder.
5. Lift the Que-lever and move the tone arm gently to the desired
position over the record.
6. Lower the Que-lever slowly.
7. Return to the tone arm to the tone arm-rest after reaching the
end of the record.
Listening to TAPE
1. Load Cassette Tape into the unit (located on side of the unit) Playback will automatically begin.
2. Press button halfway to Fast Forward the Tape. Press button lightly and playback will resume.
3. Press button all the way to end playback and eject Tape.
7
Listening to a CD
1. Press the CD button.
"--" blinks for a few seconds, when the CD exit and
enter into CD door, or the unit do not play CD.
2. Open the tray by pressing the OPEN/CLOSE button.
Then put the CD on the tray.
3. Press OPEN/CLOSE button to close the tray, then
press PLAY/PAUSE button to start playing the CD.
The CD will start playing from the first track.
4. Press the F.F button once to go the start of the next track.
5. Press the F.R button once to go back to the start of the current track.
Press the F.R button twice to go back to the start of the previous track.
Fast Reverse (F.R) and Fast Forward (F.F)
You can reverse or forward to any point in a selected track by pushing and
holding the F.R or F.F button.
NOTE: Do not push both buttons together as this may damage the unit.
As the unit is tracking quickly, forward or backward you will hear your selection playing at a distorted
speed. Simply release the depressed button to continue playing at normal speed at the desired
position in the selected track.
6. Pausing the CD play.
Pressing the PLAY/PAUSE button will restart playing the CD where it was paused
7. Stopping the CD play
8
Listening to the Radio
1. Press the AM or FM button to select the desired band.
AM
FM
2. Tune to the desired frequency.
3. FM Reception
Any strong FM station will cause the FM Stereo
Indicator (FM ST ) to illuminate.
Weaker stations cannot be received in stereo
4. Antenna
For optimal FM reception stretch the built-in FM
antenna wire located at the lower back of the unit
and move it around until the station you have
tuned in is being received clearly.
9
Troubleshooting Guide
If you experience difficulties in the use of this music system, please check the followings or call at
1-800-777-5331 for Customer Service and Support.
Problem
Cause
Solution
Power does not come on
when the power switch is
pressed.
Unit is unplugged.
Connect the unit to the AC
power supply.
No sound comes out of the
speakers.
The volume is turned down (to MIN).
The input selector does not match
the playback source.
Adjust the volume.
Re-select the desired input
source.
The sound is noisy.
The unit is too close to a TV set or
another similar appliance.
Turn off the TV or other
appliance, and relocate the
unit.
The cassette deck door
cannot be closed.
The cassette tape is not inserted
properly.
Insert
the cassette
tape
correctly.
The tape does not move.
The cassette tape is not inserted
properly.
Insert
the cassette
tape
correctly.
The tape has reached the end.
The tape heads are dirty.
Flip the cassette.
No sound from tape.
Clean the tape heads.
The sound is distorted or
faint.
The tape heads are dirty.
Clean the tape heads.
Cannot listen to any station,
or signal appears weak.
The station is not tuned-in properly.
A TV set is being used nearby and is
interfering with the radio reception.
Properly tune-in the desired
station.
Turn-off the interfering TV set.
The sound is distorted.
The antenna is not oriented properly.
Re-orient the antenna until
reception improves.
CD stops immediately after
starting, or unit pauses or
stops during play.
The CD is inserted upside down.
The CD is dusty or dirty or there is
condensation on the CD.
Insert the CD with the printed
side right-side up.
Carefully clean and dry the CD.
No sound.
The CD player is paused.
Press the PLAY/PAUSE button.
Specific CD is noisy, or
playback stops or skips.
The CD is scratched, damaged or
warped.
The CD should be changed.
Carefully clean the CD.
The disc is very dirty.
10
COMPLIANCE WITH FCC REGULATIONS
This equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-
Consult the dealer or an experienced radio technician for help.
WARNING
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
SERVICE
Please refer to the instructions on the enclosed warranty card for returning your unit for service.
Distributed by:
Spectra Merchandising International, Inc.
Chicago Industry Tech Park
4230 North Normandy Avenue
Chicago, IL 60634, U.S.A.
Please have model number ready, for Customer Service, call 1-800-777-5331
Printed in China
11
|