KRAMER ELECTRONICS LTD.
USER MANUAL
MODEL:
VP-471
3G HD-SDI to DVI Scaler
P/N: 2900-000639 Rev 7
Contents
Figures
VP-471 – Contents
i
1
Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been
providing a world of unique, creative, and affordable solutions to the vast range of
problems that confront video, audio, presentation, and broadcasting professionals
on a daily basis. In recent years, we have redesigned and upgraded most of our
line, making the best even better!
Our 1,000-plus different models now appear in 11 groups that are clearly defined
by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;
GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:
Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:
Room Connectivity; GROUP 10: Accessories and Rack Adapters and GROUP 11:
Sierra Products.
Congratulations on purchasing your Kramer VP-471 3G HD-SDI to DVI Scaler,
which is ideal for the following typical applications:
Projection systems in conference rooms, boardrooms, auditoriums, hotels
and churches, production studios, rental and staging
Home theater up-scaling
VP-471 - Introduction
1
2
Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
Review the contents of this user manual
to check for up-to-date user manuals, application programs, and to check
if firmware upgrades are available (where appropriate).
i
2.1
Achieving the Best Performance
To achieve the best performance:
Use only good quality connection cables (we recommend Kramer high-
performance, high-resolution cables) to avoid interference, deterioration in
signal quality due to poor matching, and elevated noise levels (often
associated with low quality cables)
Do not secure the cables in tight bundles or roll the slack into tight coils
Avoid interference from neighboring electrical appliances that may adversely
influence signal quality
Position your Kramer VP-471 away from moisture, excessive sunlight and
dust
This equipment is to be used only inside a building. It may only be
connected to other equipment that is installed inside a building.
!
2
VP-471 - Getting Started
2.2
2.3
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit
!
Warning: Use only the Kramer Electronics input power wall
adapter that is provided with the unit
Warning: Disconnect the power and unplug the unit from the wall
before installing
Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
aims to reduce the amount of WEEE sent for disposal to landfill or incineration by
requiring it to be collected and recycled. To comply with the WEEE Directive,
Kramer Electronics has made arrangements with the European Advanced
Recycling Network (EARN) and will cover any costs of treatment, recycling and
recovery of waste Kramer Electronics branded equipment on arrival at the EARN
facility. For details of Kramer’s recycling arrangements in your particular country
VP-471 - Getting Started
3
3
Overview
The Kramer VP-471 3G HD-SDI to DVI Scaler is a high-performance digital scaler
for signals up to 3G HD-SDI. It up and down-scales SDI, HD-SDI and 3G HD-SDI
signals to resolutions up to WUXGA and 1080p. The VP-471 supports the
following output resolutions:
PC: SVGA, XGA, 1360x768, WXGA, SXGA, 1440x900, SXGA+, WSXGA+,
UXGA, WUXGA, 720x576 @50, 720x480 (NTSC), 1280x720 @50/60 (HD
720), 1920x1080 @50/60 (HD 1080)
SDTV: 480p and 576p
HDTV: 720p @50/60Hz, 1080p @50/60Hz
The VP-471 also features:
A maximum data rate of 3Gbps
Multi-standard operation: SDI (SMPTE 259M), HD-SDI (SMPTE 292M) and
3G HD-SDI (SMPTE 424M)
An OSD (On-screen Display) accessible from the front panel buttons for
easy setup and adjustment
A built-in ProcAmp for convenient signal adjustment
A non-volatile memory that retains the last settings used
A freeze button
SDI input and loop (up to 3G HD-SDI)
A DVI video output
S/PDIF digital and unbalanced stereo audio outputs
An external 5V DC source, making it suitable for field operation
Operation directly from the front panel push buttons and the OSD
4
VP-471 - Overview
3.1
Defining the VP-471 3G HD-SDI to DVI Scaler
This section defines the VP-471.
Figure 1: VP-471 3G HD-SDI to DVI Scaler
#
1
2
3
Feature
Function
ON LED
Lights green when the unit is powered on
Lights blue when an SDI signal is detected on the input
SDI LED
MENU Button
Press to display the OSD (On-screen Display) menu.
When the OSD is not displayed, press together with the
– button to set the output resolution to 720p (1280x720)
4
ENTER Button
In the OSD, press to select the highlighted menu item.
When the OSD is not displayed, press together with the
+ button to set the output resolution to XGA
5
6
– Button
In the OSD, press to step up through the options or to
decrement the parameter value
+ / FREEZE Button
In the OSD, press to step down forward through the
options or to increment the parameter value.
When the OSD is not displayed, press to freeze the
display
7
8
SDI IN BNC Connector
Connect to the SDI source
SDI LOOP BNC Connector
Connect to the SDI acceptor. The signal is re-clocked
and equalized
9
S/PDIF RCA
Connect to a digital audio acceptor (S/PDIF)
Connector
10 AUDIO LEFT Channel
Connect to the left channel of the unbalanced stereo
audio acceptor
OUT
RCA Connector
11
RIGHT Channel
RCA Connector
Connect to the right channel of the unbalanced stereo
audio acceptor
12 DVI OUT Connector
Connect to the DVI acceptor
13 5V DC
Connect to the +5V DC power adapter, center pin
positive
VP-471 - Overview
5
4
Connecting the VP-471
Always switch off the power to each device before connecting it to your
VP-471. After connecting your VP-471, connect its power and then
i
switch on the power to each device.
To connect the VP-471 as illustrated in the example in Figure 2:
1. Connect the digital SDI camera to the SDI IN BNC connector.
2. Connect the SDI LOOP BNC connector to an SDI display.
3. Connect the S/PDIF AUDIO OUT RCA connector to the digital AV receiver.
4. Connect the LEFT and RIGHT AUDIO OUT RCA connectors to the
unbalanced stereo audio amplifier.
5. Connect the DVI OUT connector to the DVI projector.
6. Connect the 5V DC power adapter to 5V DC power socket and to the mains
electricity (not shown in the illustration).
6
VP-471 - Connecting the VP-471
5
Operating the VP-471 3G HD-SDI to DVI
Scaler
5.1
Using the Front Panel Buttons
During normal operation (without the OSD), the front panel buttons perform in the
following manner:
time to close the OSD
FREEZE: Freezes the display. Press a second time to unfreeze the display
MENU and AUTO ADJUST: Press together to set the output to 720p
(1280x720)
ENTER and FREEZE: Press together to set the output to XGA (1024x768)
5.2
Using the OSD
The OSD is used to set a variety of parameters.
When using the OSD, the front panel buttons operate in the following manner:
time to close the OSD
ENTER: Selects the highlighted menu item or parameter
– : Steps up through the menu list or decrements the parameter value
+ : Steps down through the menu list or increments the parameter value
Note: After a period of 15 sec with no button activity, the OSD menu times-out
automatically.
8
VP-471 - Operating the VP-471 3G HD-SDI to DVI Scaler
Parameter Setting Example:
To set the green offset value of the display output to 42:
1. From normal operation, press MENU.
The OSD main menu appears on the screen.
2. Press the + or – button to highlight COLOR.
COLOR changes to green.
3. Press ENTER.
The Display submenu is displayed.
4. Press the + or – button to highlight G OFFSET.
G OFFSET changes to green.
5. Press ENTER.
The G OFFSET parameter changes to red.
6. Press the + button to increase the value to 42.
7. Press ENTER to set the value.
G OFFSET is highlighted in green.
8. To exit normal operation, press MENU.
5.2.1
The Main Menu
The following table defines the Main menu parameters and functions.
Parameter
DISPLAY
COLOR
Function
SDI AUDIO
Selects which embedded audio to output: Group 1, Group 2, Group 3,
Group 4, Auto, Off (audio is not outputted) Default: Auto
When set to Auto, the unit searches for the lowest Group number
which has audio and selects this audio Group
FACTORY RESET
INFORMATION
Resets all parameters to factory defaults
Displays current input resolution, output resolution and firmware
revision
AUTO SYNC OFF
When on, this de-activates the output after a few minutes if no input is
present
When set to Auto, the unit searches for the lowest Group number which
has audio and selects this audio Group
EXIT
Exits the Main menu
VP-471 - Operating the VP-471 3G HD-SDI to DVI Scaler
9
5.2.2 The Display Submenu
The Display submenu sets the display output resolution, size and aspect ratio.
The following table defines the display output parameters.
Parameter
Parameters
Factory
Default
OUTPUT
Sets the output resolution.
1024x768
@60
Native, 1920x1080p @50 (HD 1080), 1280x720p @50 (HD
720), 720x576p @50, 1920x1080p (HD 1080), 1280x720p
(HD 720), 720x480p (NTSC), 1920x1200p (WUXGA),
1600x1200 (UXGA), 1680x1050 (WSXGA+), 1400x1050
(SXGA+), 1440x900, 1280x1024 (SXGA), 1280x800
(WXGA), 1360x768, 1280x768 (WXGA), 1024x768 (XGA),
800x600 (SVGA)
PC: VGA, SVGA, XGA, 1280x800, UXGA, SXGA, WXGA,
SXGA+, WXGA+, WSXGA, WUXGA
SDTV: 480p and 576p
HDTV: 720p @50/60Hz, 1080p @50/60Hz
SIZE
EXIT
Sets the output size/aspect ratio: Full, Pan scan, Letter box,
Under 2, Under 1, Over scan
Full
Exits the Display menu
5.2.3 The Color Submenu
The Color submenu sets the display output color parameters. The following table
defines the color output parameters.
Parameter
Function
Value
Range
Factory
Default
CONTRAST
Sets the output contrast
0-255
0-192
0-255
0-255
0-255
0-63
105
96
BRIGHTNESS Sets the output brightness
R
Sets the output red value
128
128
128
32
G
Sets the output green value
B
Sets the output blue value
R OFFSET
G OFFSET
B OFFSET
EXIT
Sets the output red signal level offset
Sets the output green signal level offset
Sets the output blue signal level offset
Exits the Color submenu
0-63
32
0-63
32
10
VP-471 - Operating the VP-471 3G HD-SDI to DVI Scaler
6
Technical Specifications
INPUT:
1 SD/HD/3G HD-SDI plus loop on a BNC connector
OUTPUTS:
1 DVI-D on DVI-I connector, 1 S/PDIF digital audio on an
RCA connector, 1 unbalanced stereo audio on 2 RCA
connectors
INPUT RESOLUTIONS:
480i @59.94Hz, 576i @50Hz, 720p @50/60Hz, 1080p
@24/25/30/50/60Hz, 1080i @50/60Hz
OUTPUT RESOLUTIONS:
Native, 1920x1080p @50 (HD 1080), 1280x720p @50 (HD
720), 720x576p @50, 1920x1080p (HD 1080), 1280x720p
(HD 720), 720x480p (NTSC), 1920x1200p (WUXGA),
1600x1200 (UXGA), 1680x1050 (WSXGA+), 1400x1050
(SXGA+), 1440x900, 1280x1024 (SXGA), 1280x800
(WXGA), 1360x768, 1280x768 (WXGA), 1024x768 (XGA),
800x600 (SVGA)
PC: VGA, SVGA, XGA, 1280x800, UXGA, SXGA, WXGA,
SXGA+, WXGA+, WSXGA, WUXGA
SDTV: 480p @60Hz and 576p @50Hz
HDTV: 720p @50/60Hz, 1080p @50/60Hz
All resolutions are outputted @60Hz, except where noted
OUTPUT REFRESH RATE:
60Hz for computer graphics resolutions, 50/60Hz for HDTV
resolutions
OUTPUT SIZE
Full, panscan, letterbox, under 2, under 1, overscan
30ms
PROCESSING DELAY:
CONTROLS:
Menu, OSD and Freeze front panel buttons
5V DC, 1.35A
POWER CONSUMPTION:
OPERATING TEMPERATURE:
STORAGE TEMPERATURE:
HUMIDITY:
0° to +40°C (32° to 104°F)
-40° to +70°C (-40° to 158°F)
10% to 90%, RHL non-condensing
18.8cm x 11.4cm x 2.4cm (7.4” x 4.5” x 1”) W, D, H
0.75kg (1.7lbs) approx.
DIMENSIONS:
WEIGHT:
ACCESSORIES:
OPTIONS:
Power supply
RK-T2B 19" rack adapter
VP-471 - Technical Specifications
11
For the latest information on our products and a list of Kramer distributors,
visit our Web site where updates to this user manual may be found.
We welcome your questions, comments, and feedback.
Web site: www.kramerelectronics.com
E-mail: [email protected]
SAFETY WARNING
Disconnect the unit from the power
supply before opening and servicing
!
P/N:
Rev:
2900- 000639
7
|
